SNMP-NOTIFICATION-MIB - Man Page
SNMP-NOTIFICATION-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
snmpModules
FROM SNMPv2-SMI
RowStatus,
StorageType
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
SnmpTagValue,
snmpTargetParamsName
FROM SNMP-TARGET-MIB
MODULE-COMPLIANCE,
OBJECT-GROUP
FROM SNMPv2-CONF;
snmpNotificationMIB MODULE-IDENTITY
LAST-UPDATED "9808040000Z"
ORGANIZATION "IETF SNMPv3 Working Group"
CONTACT-INFO
"WG-email: snmpv3@tis.com
Subscribe: majordomo@tis.com
In message body: subscribe snmpv3
Chair: Russ Mundy
Trusted Information Systems
Postal: 3060 Washington Rd
Glenwood MD 21738
USA
EMail: mundy@tis.com
Phone: +1-301-854-6889
Co-editor: David B. Levi
SNMP Research, Inc.
Postal: 3001 Kimberlin Heights Road
Knoxville, TN 37920-9716
EMail: levi@snmp.com
Phone: +1 423 573 1434
Co-editor: Paul Meyer
Secure Computing Corporation
Postal: 2675 Long Lake Road
Roseville, MN 55113
EMail: paul_meyer@securecomputing.com
Phone: +1 651 628 1592
Co-editor: Bob Stewart
Cisco Systems, Inc.
Postal: 170 West Tasman Drive
San Jose, CA 95134-1706
EMail: bstewart@cisco.com
Phone: +1 603 654 2686"
DESCRIPTION
"This MIB module defines MIB objects which provide
mechanisms to remotely configure the parameters
used by an SNMP entity for the generation of
notifications."
REVISION "9808040000Z"
DESCRIPTION "Clarifications, published as
draft-ietf-snmpv3-appl-v2-01.txt."
REVISION "9707140000Z"
DESCRIPTION "The initial revision, published as RFC2273."
::= { snmpModules 13 }
snmpNotifyObjects OBJECT IDENTIFIER ::=
{ snmpNotificationMIB 1 }
snmpNotifyConformance OBJECT IDENTIFIER ::=
{ snmpNotificationMIB 3 }
--
--
-- The snmpNotifyObjects group
--
--
snmpNotifyTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnmpNotifyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to select management targets which should
receive notifications, as well as the type of notification
which should be sent to each selected management target."
::= { snmpNotifyObjects 1 }
snmpNotifyEntry OBJECT-TYPE
SYNTAX SnmpNotifyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table selects a set of management targets
which should receive notifications, as well as the type of
notification which should be sent to each selected
management target.
Entries in the snmpNotifyTable are created and
deleted using the snmpNotifyRowStatus object."
INDEX { IMPLIED snmpNotifyName }
::= { snmpNotifyTable 1 }
SnmpNotifyEntry ::= SEQUENCE {
snmpNotifyName SnmpAdminString,
snmpNotifyTag SnmpTagValue,
snmpNotifyType INTEGER,
snmpNotifyStorageType StorageType,
snmpNotifyRowStatus RowStatus
}
snmpNotifyName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The locally arbitrary, but unique identifier associated
with this snmpNotifyEntry."
::= { snmpNotifyEntry 1 }
snmpNotifyTag OBJECT-TYPE
SYNTAX SnmpTagValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object contains a single tag value which is used
to select entries in the snmpTargetAddrTable. Any entry
in the snmpTargetAddrTable which contains a tag value
which is equal to the value of an instance of this
object is selected. If this object contains a value
of zero length, no entries are selected."
DEFVAL { "" }
::= { snmpNotifyEntry 2 }
snmpNotifyType OBJECT-TYPE
SYNTAX INTEGER {
trap(1),
inform(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object determines the type of notification to
be generated for entries in the snmpTargetAddrTable
selected by the corresponding instance of
snmpNotifyTag. This value is only used when
generating notifications, and is ignored when
using the snmpTargetAddrTable for other purposes.
If the value of this object is trap(1), then any
messages generated for selected rows will contain
Unconfirmed-Class PDUs.
If the value of this object is inform(2), then any
messages generated for selected rows will contain
Confirmed-Class PDUs.
Note that if an SNMP entity only supports
generation of Unconfirmed-Class PDUs (and not
Confirmed-Class PDUs), then this object may be
read-only."
DEFVAL { trap }
::= { snmpNotifyEntry 3 }
snmpNotifyStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row."
DEFVAL { nonVolatile }
::= { snmpNotifyEntry 4 }
snmpNotifyRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row.
To create a row in this table, a manager must
set this object to either createAndGo(4) or
createAndWait(5)."
::= { snmpNotifyEntry 5 }
snmpNotifyFilterProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnmpNotifyFilterProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is used to associate a notification filter
profile with a particular set of target parameters."
::= { snmpNotifyObjects 2 }
snmpNotifyFilterProfileEntry OBJECT-TYPE
SYNTAX SnmpNotifyFilterProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table indicates the name of the filter
profile to be used when generating notifications using
the corresponding entry in the snmpTargetParamsTable.
Entries in the snmpNotifyFilterProfileTable are created
and deleted using the snmpNotifyFilterProfileRowStatus
object."
INDEX { IMPLIED snmpTargetParamsName }
::= { snmpNotifyFilterProfileTable 1 }
SnmpNotifyFilterProfileEntry ::= SEQUENCE {
snmpNotifyFilterProfileName SnmpAdminString,
snmpNotifyFilterProfileStorType StorageType,
snmpNotifyFilterProfileRowStatus RowStatus
}
snmpNotifyFilterProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name of the filter profile to be used when generating
notifications using the corresponding entry in the
snmpTargetAddrTable."
::= { snmpNotifyFilterProfileEntry 1 }
snmpNotifyFilterProfileStorType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type of this conceptual row."
DEFVAL { nonVolatile }
::= { snmpNotifyFilterProfileEntry 2 }
snmpNotifyFilterProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row.
To create a row in this table, a manager must
set this object to either createAndGo(4) or
createAndWait(5).
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the
snmpNotifyFilterProfileRowStatus column is 'notReady'.
In particular, a newly created row cannot be made
active until the corresponding instance of
snmpNotifyFilterProfileName has been set."
::= { snmpNotifyFilterProfileEntry 3 }
snmpNotifyFilterTable OBJECT-TYPE
SYNTAX SEQUENCE OF SnmpNotifyFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table of filter profiles. Filter profiles are used
to determine whether particular management targets should
receive particular notifications.
When a notification is generated, it must be compared
with the filters associated with each management target
which is configured to receive notifications, in order to
determine whether it may be sent to each such management
target.
A more complete discussion of notification filtering
can be found in section 6. of [SNMP-APPL]."
::= { snmpNotifyObjects 3 }
snmpNotifyFilterEntry OBJECT-TYPE
SYNTAX SnmpNotifyFilterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An element of a filter profile.
Entries in the snmpNotifyFilterTable are created and
deleted using the snmpNotifyFilterRowStatus object."
INDEX { snmpNotifyFilterProfileName,
IMPLIED snmpNotifyFilterSubtree }
::= { snmpNotifyFilterTable 1 }
SnmpNotifyFilterEntry ::= SEQUENCE {
snmpNotifyFilterSubtree OBJECT IDENTIFIER,
snmpNotifyFilterMask OCTET STRING,
snmpNotifyFilterType INTEGER,
snmpNotifyFilterStorageType StorageType,
snmpNotifyFilterRowStatus RowStatus
}
snmpNotifyFilterSubtree OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MIB subtree which, when combined with the corresponding
instance of snmpNotifyFilterMask, defines a family of
subtrees which are included in or excluded from the
filter profile."
::= { snmpNotifyFilterEntry 1 }
snmpNotifyFilterMask OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..16))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The bit mask which, in combination with the corresponding
instance of snmpNotifyFilterSubtree, defines a family of
subtrees which are included in or excluded from the
filter profile.
Each bit of this bit mask corresponds to a
sub-identifier of snmpNotifyFilterSubtree, with the
most significant bit of the i-th octet of this octet
string value (extended if necessary, see below)
corresponding to the (8*i - 7)-th sub-identifier, and
the least significant bit of the i-th octet of this
octet string corresponding to the (8*i)-th
sub-identifier, where i is in the range 1 through 16.
Each bit of this bit mask specifies whether or not
the corresponding sub-identifiers must match when
determining if an OBJECT IDENTIFIER matches this
family of filter subtrees; a '1' indicates that an
exact match must occur; a '0' indicates 'wild card',
i.e., any sub-identifier value matches.
Thus, the OBJECT IDENTIFIER X of an object instance
is contained in a family of filter subtrees if, for
each sub-identifier of the value of
snmpNotifyFilterSubtree, either:
the i-th bit of snmpNotifyFilterMask is 0, or
the i-th sub-identifier of X is equal to the i-th
sub-identifier of the value of
snmpNotifyFilterSubtree.
If the value of this bit mask is M bits long and
there are more than M sub-identifiers in the
corresponding instance of snmpNotifyFilterSubtree,
then the bit mask is extended with 1's to be the
required length.
Note that when the value of this object is the
zero-length string, this extension rule results in
a mask of all-1's being used (i.e., no 'wild card'),
and the family of filter subtrees is the one
subtree uniquely identified by the corresponding
instance of snmpNotifyFilterSubtree."
DEFVAL { ''H }
::= { snmpNotifyFilterEntry 2 }
snmpNotifyFilterType OBJECT-TYPE
SYNTAX INTEGER {
included(1),
excluded(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates whether the family of filter subtrees
defined by this entry are included in or excluded from a
filter. A more detailed discussion of the use of this
object can be found in section 6. of [SNMP-APPL]."
DEFVAL { included }
::= { snmpNotifyFilterEntry 3 }
snmpNotifyFilterStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type of this conceptual row."
DEFVAL { nonVolatile }
::= { snmpNotifyFilterEntry 4 }
snmpNotifyFilterRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row.
To create a row in this table, a manager must
set this object to either createAndGo(4) or
createAndWait(5)."
::= { snmpNotifyFilterEntry 5 }
--
--
-- Conformance information
--
--
snmpNotifyCompliances OBJECT IDENTIFIER ::=
{ snmpNotifyConformance 1 }
snmpNotifyGroups OBJECT IDENTIFIER ::=
{ snmpNotifyConformance 2 }
--
--
-- Compliance statements
--
--
snmpNotifyBasicCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for minimal SNMP entities which
implement only SNMP Unconfirmed-Class notifications and
read-create operations on only the snmpTargetAddrTable."
MODULE SNMP-TARGET-MIB
MANDATORY-GROUPS { snmpTargetBasicGroup }
OBJECT snmpTargetParamsMPModel
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required."
OBJECT snmpTargetParamsSecurityModel
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required."
OBJECT snmpTargetParamsSecurityName
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required."
OBJECT snmpTargetParamsSecurityLevel
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required."
OBJECT snmpTargetParamsStorageType
SYNTAX INTEGER {
readOnly(5)
}
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required.
Support of the values other(1), volatile(2),
nonVolatile(3), and permanent(4) is not required."
OBJECT snmpTargetParamsRowStatus
SYNTAX INTEGER {
active(1)
}
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access to the
snmpTargetParamsTable is not required.
Support of the values notInService(2), notReady(3),
createAndGo(4), createAndWait(5), and destroy(6) is
not required."
MODULE -- This Module
MANDATORY-GROUPS { snmpNotifyGroup }
OBJECT snmpNotifyTag
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required."
OBJECT snmpNotifyType
SYNTAX INTEGER {
trap(1)
}
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required.
Support of the value notify(2) is not required."
OBJECT snmpNotifyStorageType
SYNTAX INTEGER {
readOnly(5)
}
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access is not required.
Support of the values other(1), volatile(2),
nonVolatile(3), and permanent(4) is not required."
OBJECT snmpNotifyRowStatus
SYNTAX INTEGER {
active(1)
}
MIN-ACCESS read-only
DESCRIPTION
"Create/delete/modify access to the
snmpNotifyTable is not required.
Support of the values notInService(2), notReady(3),
createAndGo(4), createAndWait(5), and destroy(6) is
not required."
::= { snmpNotifyCompliances 1 }
snmpNotifyBasicFiltersCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which implement
SNMP Unconfirmed-Class notifications with filtering, and
read-create operations on all related tables."
MODULE SNMP-TARGET-MIB
MANDATORY-GROUPS { snmpTargetBasicGroup }
MODULE -- This Module
MANDATORY-GROUPS { snmpNotifyGroup,
snmpNotifyFilterGroup }
::= { snmpNotifyCompliances 2 }
snmpNotifyFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which either
implement only SNMP Confirmed-Class notifications, or both
SNMP Unconfirmed-Class and Confirmed-Class notifications,
plus filtering and read-create operations on all related
tables."
MODULE SNMP-TARGET-MIB
MANDATORY-GROUPS { snmpTargetBasicGroup,
snmpTargetResponseGroup }
MODULE -- This Module
MANDATORY-GROUPS { snmpNotifyGroup,
snmpNotifyFilterGroup }
::= { snmpNotifyCompliances 3 }
snmpNotifyGroup OBJECT-GROUP
OBJECTS {
snmpNotifyTag,
snmpNotifyType,
snmpNotifyStorageType,
snmpNotifyRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects for selecting which management
targets are used for generating notifications, and the
type of notification to be generated for each selected
management target."
::= { snmpNotifyGroups 1 }
snmpNotifyFilterGroup OBJECT-GROUP
OBJECTS {
snmpNotifyFilterProfileName,
snmpNotifyFilterProfileStorType,
snmpNotifyFilterProfileRowStatus,
snmpNotifyFilterMask,
snmpNotifyFilterType,
snmpNotifyFilterStorageType,
snmpNotifyFilterRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing remote configuration
of notification filters."
::= { snmpNotifyGroups 2 }
ENDInfo
SNMP Erlang/OTP MIB