DS2755 - Man Page

35 [.]XXXXXXXXXXXX[XX][/[ alarm_set/[volthigh|voltlow|temphigh|templow] | lock.[0-2|ALL] | memory | pages/page.[0-2|ALL] | Pio | sensed | temperature | vbias | vis | volt | volthours |
defaultpmod | pie0 | pie1 | rnaop | ios | uben | ovd | pmod | por | uven |
address | crc8 | id | locator | r_address | r_id | r_locator | type ]]

35 [.]XXXXXXXXXXXX[XX][/[ temperature | typeX/range_low | typeX/range_high | typeX/temperature

read-write, integer
High and low alarm settings for temperature

read-write, floating point
High and low alarm settings for volts

read-write, yes-no
Lock any of the three eprom pages to prevent further writes. Apparently setting lock is permanent.

read-write, binary
Access to the full 256 byte memory range. Much of this space is reserved or special use. User space is the page area.
See the Datasheet for a full memory map.

read-write, binary Three 32 byte areas of memory for user application. The lock property can prevent further alteration.
NOTE that the page property is different from the common OWFS implementation in that all of memory is not accessible.

write-only, yes-no
Controls the PIO pin allowing external switching.
Writing "1" turns the PIO pin on (conducting). Writing "0" makes the pin non-conducting. The logical state of the voltage can be read with the sensed property. This will reflect the current voltage at the pin, not the value sent to PIO
Note also that PIO will also be altered by the power-status of the DS2670 See the datasheet for details.

read-only, yes-no
The logical voltage at the Pio pin. Useful only if the Pio property is set to "0" (non-conducting).
Value will be 0 or 1 depending on the voltage threshold.

read-only, floating point
Temperature read by the chip at high resolution (~13 bits). Units are selected from the invoking command line. See owfs(1) or owhttpd(1) for choices. Default is Celsius.
Conversion is continuous.

read-write, floating point
Fixed offset applied to each vis measurement. Used for the volthours value. Units are in Volts.
Range -2.0mV to 2.0mV

read-only, floating point
Current sensor reading (unknown external resistor). Measures the voltage gradient between the Vis pins. Units are in Volts
The vis readings are integrated over time to provide the volthours property.
The current reading is derived from vis assuming the internal 25 mOhm resistor is employed. There is no way to know this through software.

read-only, floating point
Voltage read at the voltage sensor;. This is separate from the vis voltage that is used for current measurement. Units are Volts
Range is between 0 and 4.75V

read-write, floating point
Integral of vis - vbias over time. Units are in volthours

directory
Thermocouple circuit using the DS2755 to read the Seebeck voltage and the reference temperature. Since the type interpretation of the values read depends on the type of thermocouple, the correct directory must be chosen. Supported thermocouple types include types B, E, J, K, N, R, S and T.

read-only, flaoting point
The lower and upper temperature supported by this thermocouple (at least by the conversion routines). In the globally chosen temperature units.

read-only, floating point
Thermocouple temperature. Requires a voltage and temperature conversion. Returned in globally chosen temperature units.
Note: there are two types of temperature measurements possible. The temperature value in the main device directory is the reference temperature read at the chip. The typeX/temperature value is at the thermocouple junction, probably remote from the chip.

varies, yes-no
Bit flags corresponding to various battery management functions of the chip. See the Datasheet for details of the identically named entries.
In general, writing "0" corresponds to a 0 bit value, and non-zero corresponds to a 1 bit value.

read-write, yes-no
Default power-on state for the corresponding properties.

read-only, ascii
The entire 64-bit unique Id. Given as upper case hexadecimal digits (0-9A-F).
address starts with the family code
r address is the address in reverse order, which is often used in other applications and labeling.

read-only, ascii
The 8-bit error correction portion. Uses cyclic redundancy check. Computed from the preceding 56 bits of the unique Id number. Given as upper case hexadecimal digits (0-9A-F).

read-only, ascii
The 8-bit family code. Unique to each type of device. Given as upper case hexadecimal digits (0-9A-F).

read-only, ascii
The 48-bit middle portion of the unique Id number. Does not include the family code or CRC. Given as upper case hexadecimal digits (0-9A-F).
r id is the id in reverse order, which is often used in other applications and labeling.

read-only, ascii
Uses an extension of the 1-wire design from iButtonLink company that associated 1-wire physical connections with a unique 1-wire code. If the connection is behind a Link Locator the locator will show a unique 8-byte number (16 character hexadecimal) starting with family code FE.
If no Link Locator is between the device and the master, the locator field will be all FF.
r locator is the locator in reverse order.

read-only, yes-no
Is the device currently present on the 1-wire bus?

read-only, ascii
Part name assigned by Dallas Semi. E.g. DS2401 Alternative packaging (iButton vs chip) will not be distiguished.

1-wire is a wiring protocol and series of devices designed and manufactured by Dallas Semiconductor, Inc. The bus is a low-power low-speed low-connector scheme where the data line can also provide power.

Each device is uniquely and unalterably numbered during manufacture. There are a wide variety of devices, including memory, sensors (humidity, temperature, voltage, contact, current), switches, timers and data loggers. More complex devices (like thermocouple sensors) can be built with these basic devices. There are also 1-wire devices that have encryption included.

The 1-wire scheme uses a single bus master and multiple slaves on the same wire. The bus master initiates all communication. The slaves can be  individually discovered and addressed using their unique Id.

Bus masters come in a variety of configurations including serial, parallel, i2c, network or USB adapters.

OWFS is a suite of programs that designed to make the 1-wire bus and its devices easily accessible. The underlying principle is to create a virtual filesystem, with the unique Id being the directory, and the individual properties of the device are represented as simple files that can be read and written.

Details of the individual slave or master design are hidden behind a consistent interface. The goal is to  provide an easy set of tools for a software designer to create monitoring or control applications. There  are some performance enhancements in the implementation, including data caching, parallel access to bus  masters, and aggregation of device communication. Still the fundamental goal has been ease of use, flexibility and correctness rather than speed.

The DS2755 (3) and DS2756 (3) are battery charging controllers similar to the DS2751 (3) except no internal resistor option and a larger EEPROM memory.

The DS2756 (3) adds suspend modes ( pie0 pie1 ) to the DS2755 (3)

A number of interesting devices can be built with the DS2755 (3) and DS2756 (3) including thermocouples. Support for thermocouples in built into the software, using the embedded thermister as the cold junction temperature.

owfs (1) owhttpd (1) owftpd (1) owserver (1) owdir (1) owread (1) owwrite (1) owpresent (1) owtap (1)

owfs (5) owtap (1) owmon (1)

owtcl (3) owperl (3) owcapi (3)

DS1427 (3) DS1904 (3) DS1994 (3) DS2404 (3) DS2404S (3) DS2415 (3) DS2417 (3)

DS2401 (3) DS2411 (3) DS1990A (3)

DS1982 (3) DS1985 (3) DS1986 (3) DS1991 (3) DS1992 (3) DS1993 (3) DS1995 (3) DS1996 (3) DS2430A (3) DS2431 (3) DS2433 (3) DS2502 (3) DS2506 (3) DS28E04 (3) DS28EC20 (3)

DS2405 (3) DS2406 (3) DS2408 (3) DS2409 (3) DS2413 (3) DS28EA00 (3) InfernoEmbedded (3)

DS1822 (3) DS1825 (3) DS1820 (3) DS18B20 (3) DS18S20 (3) DS1920 (3) DS1921 (3) DS1821 (3) DS28EA00 (3) DS28E04 (3) EDS0064 (3) EDS0065 (3) EDS0066 (3) EDS0067 (3) EDS0068 (3) EDS0071 (3) EDS0072 (3) MAX31826 (3)

DS1922 (3) DS2438 (3) EDS0065 (3) EDS0068 (3)

DS2450 (3)

DS2890 (3)

DS2436 (3) DS2437 (3) DS2438 (3) DS2751 (3) DS2755 (3) DS2756 (3) DS2760 (3) DS2770 (3) DS2780 (3) DS2781 (3) DS2788 (3) DS2784 (3)

DS2423 (3)

LCD (3) DS2408 (3)

DS1977 (3)

DS2406 (3) TAI8570 (3) EDS0066 (3) EDS0068 (3)

EEEF (3) DS2438 (3)