rtl_433 - Man Page

[ -V ]

Output the version string and exit

[ -v ]

Increase verbosity (can be used multiple times).
      -v : verbose notice, -vv : verbose info, -vvv : debug, -vvvv : trace.

[ -c <path> ]

Read config options from a file

[ -d <RTL-SDR USB device index> | :<RTL-SDR USB device serial> | <SoapySDR device query> | rtl_tcp | help ]

[-g <gain> | help] (default: auto)

[ -t <settings> ]

apply a list of keyword=value settings to the SDR device
      e.g. for SoapySDR -t "antenna=A,bandwidth=4.5M,rfnotch_ctrl=false"
      for RTL-SDR use "direct_samp[=1]", "offset_tune[=1]", "digital_agc[=1]", "biastee[=1]"

[ -f <frequency> ]

Receive frequency(s) (default: 433920000 Hz)

[ -H <seconds> ]

Hop interval for polling of multiple frequencies (default: 600 seconds)

[ -p <ppm_error> ]

Correct rtl-sdr tuner frequency offset error (default: 0)

[ -s <sample rate> ]

Set sample rate (default: 250000 Hz)

[ -D restart | pause | quit | manual ]

Input device run mode options.

[ -R <device> | help ]

Enable only the specified device decoding protocol (can be used multiple times)
      Specify a negative number to disable a device decoding protocol (can be used multiple times)

[ -X <spec> | help ]

Add a general purpose decoder (prepend -R 0 to disable all decoders)

[ -Y auto | classic | minmax ]

FSK pulse detector mode.

[ -Y level=<dB level> ]

Manual detection level used to determine pulses (-1.0 to -30.0) (0=auto).

[ -Y minlevel=<dB level> ]

Manual minimum detection level used to determine pulses (-1.0 to -99.0).

[ -Y minsnr=<dB level> ]

Minimum SNR to determine pulses (1.0 to 99.0).

[ -Y autolevel ]

Set minlevel automatically based on average estimated noise.

[ -Y squelch ]

Skip frames below estimated noise level to reduce cpu load.

[ -Y ampest | magest ]

Choose amplitude or magnitude level estimator.

[ -A ]

Pulse Analyzer. Enable pulse analysis and decode attempt.
      Disable all decoders with -R 0 if you want analyzer output only.

[ -y <code> ]

Verify decoding of demodulated test data (e.g. "{25}fb2dd58") with enabled devices

[ -S none | all | unknown | known ]

Signal auto save. Creates one file per signal.
      Note: Saves raw I/Q samples (uint8 pcm, 2 channel). Preferred mode for generating test files.

[ -r <filename> | help ]

Read data from input file instead of a receiver

[ -w <filename> | help ]

Save data stream to output file (a '-' dumps samples to stdout)

[ -W <filename> | help ]

Save data stream to output file, overwrite existing file

[ -F log | kv | json | csv | mqtt | influx | syslog | trigger | null | help ]

Produce decoded output in given format.
      Append output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout.
      Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514

[ -M time[:<options>] | protocol | level | noise[:<secs>] | stats | bits | help ]

Add various meta data to each output.

[ -K FILE | PATH | <tag> | <key>=<tag> ]

Add an expanded token or fixed tag to every output line.

[ -C native | si | customary ]

Convert units in decoded output.

[ -n <value> ]

Specify number of samples to take (each sample is an I/Q pair)

[ -T <seconds> ]

Specify number of seconds to run, also 12:34 or 1h23m45s

[ -E hop | quit ]

Hop/Quit after outputting successful event(s)

[ -h ]

Output this usage help and exit
      Use -d, -g, -R, -X, -F, -M, -r, -w, or -W without argument for more help

[ -d <RTL-SDR USB device index> ]

(default: 0)

[ -d :<RTL-SDR USB device serial (can be set with rtl_eeprom -s)> ]

To set gain for RTL-SDR use -g <gain> to set an overall gain in dB.
SoapySDR device driver is available.

[ -d "" ]

Open default SoapySDR device

[ -d driver=rtlsdr ]

Open e.g. specific SoapySDR device
To set gain for SoapySDR use -g ELEM=val,ELEM=val,... e.g. -g LNA=20,TIA=8,PGA=2 (for LimeSDR).

[ -d rtl_tcp[:[//]host[:port] ]

(default: localhost:1234)
Specify host/port to connect to with e.g. -d rtl_tcp:127.0.0.1:1234

[ -g <gain> ]

(default: auto)
For RTL-SDR: gain in dB ("0" is auto).
For SoapySDR: gain in dB for automatic distribution ("" is auto), or string of gain elements.
E.g. "LNA=20,TIA=8,PGA=2" for LimeSDR.

Use -X <spec> to add a flexible general purpose decoder.

<spec> is "key=value[,key=value...]" Common keys are:

where: <name> can be any descriptive name tag you need in the output <modulation> is one of:

<short>, <long>, <sync> are nominal modulation timings in us, <reset>, <gap>, <tolerance> are maximum modulation timings in us: PCM/RZ  short: Nominal width of pulse [us]
        long: Nominal width of bit period [us] PPM     short: Nominal width of '0' gap [us]
        long: Nominal width of '1' gap [us] PWM     short: Nominal width of '1' pulse [us]
        long: Nominal width of '0' pulse [us]
        sync: Nominal width of sync pulse [us] (optional) common    gap: Maximum gap size before new row of bits [us]
       reset: Maximum gap size before End Of Message [us]
   tolerance: Maximum pulse deviation [us] (optional). Available options are:

E.g. -X "n=doorbell,m=OOK_PWM,s=400,l=800,r=7000,g=1000,match={24}0xa9878c,repeats>=3"

[ -F log|kv|json|csv|mqtt|influx|syslog|trigger|null ]

Produce decoded output in given format.
Without this option the default is LOG and KV output. Use "-F null" to remove the default.
Append output to file with :<filename> (e.g. -F csv:log.csv), defaults to stdout.
Specify MQTT server with e.g. -F mqtt://localhost:1883
Add MQTT options with e.g. -F "mqtt://host:1883,opt=arg"
MQTT options are: user=foo, pass=bar, retain[=0|1], <format>[=topic]
Default user and password are read from MQTT_USERNAME and MQTT_PASSWORD env vars.
A base topic can be set with base=<topic>, default is "rtl_433/HOSTNAME".
Supported MQTT formats: (default is all)
 events: posts JSON event data
 states: posts JSON state data
 devices: posts device and sensor info in nested topics
Any topic string overrides the base topic and will expand keys like [/model]
E.g. -F "mqtt://localhost:1883,user=USERNAME,pass=PASSWORD,retain=0,devices=rtl_433[/id]"
With MQTT each rtl_433 instance needs a distinct driver selection. The MQTT Client-ID is computed from the driver string.
If you use multiple RTL-SDR, perhaps set a serial and select by that (helps not to get the wrong antenna).
Specify InfluxDB 2.0 server with e.g. -F "influx://localhost:9999/api/v2/write?org=<org>&bucket=<bucket>,token=<authtoken>"
Specify InfluxDB 1.x server with e.g. -F "influx://localhost:8086/write?db=<db>&p=<password>&u=<user>"
 Additional parameter -M time:unix:usec:utc for correct timestamps in InfluxDB recommended
Specify host/port for syslog with e.g. -F syslog:127.0.0.1:1514

[ -M time[:<options>]|protocol|level|noise[:<secs>]|stats|bits ]

Add various metadata to every output line.
Use "time" to add current date and time meta data (preset for live inputs).
Use "time:rel" to add sample position meta data (preset for read-file and stdin).
Use "time:unix" to show the seconds since unix epoch as time meta data. This is always UTC.
Use "time:iso" to show the time with ISO-8601 format (YYYY-MM-DD"T"hh:mm:ss).
Use "time:off" to remove time meta data.
Use "time:usec" to add microseconds to date time meta data.
Use "time:tz" to output time with timezone offset.
Use "time:utc" to output time in UTC.
(this may also be accomplished by invocation with TZ environment variable set).
"usec" and "utc" can be combined with other options, eg. "time:iso:utc" or "time:unix:usec".
Use "replay[:N]" to replay file inputs at (N-times) realtime.
Use "protocol" / "noprotocol" to output the decoder protocol number meta data.
Use "level" to add Modulation, Frequency, RSSI, SNR, and Noise meta data.
Use "noise[:<secs>]" to report estimated noise level at intervals (default: 10 seconds).
Use "stats[:[<level>][:<interval>]]" to report statistics (default: 600 seconds).
 level 0: no report, 1: report successful devices, 2: report active devices, 3: report all
Use "bits" to add bit representation to code outputs (for debug).

[ -r <filename> ]

Read data from input file instead of a receiver
Parameters are detected from the full path, file name, and extension.

A center frequency is detected as (fractional) number suffixed with 'M',
'Hz', 'kHz', 'MHz', or 'GHz'.

A sample rate is detected as (fractional) number suffixed with 'k',
'sps', 'ksps', 'Msps', or 'Gsps'.

File content and format are detected as parameters, possible options are:
'cu8', 'cs16', 'cf32' ('IQ' implied), and 'am.s16'.

Parameters must be separated by non-alphanumeric chars and are case-insensitive.
Overrides can be prefixed, separated by colon (':')

E.g. default detection by extension: path/filename.am.s16
forced overrides: am:s16:path/filename.ext

Reading from pipes also support format options.
E.g reading complex 32-bit float: CU32:-

[ -w <filename> ]

Save data stream to output file (a '-' dumps samples to stdout)

[ -W <filename> ]

Save data stream to output file, overwrite existing file
Parameters are detected from the full path, file name, and extension.

File content and format are detected as parameters, possible options are:
'cu8', 'cs8', 'cs16', 'cf32' ('IQ' implied),
'am.s16', 'am.f32', 'fm.s16', 'fm.f32',
'i.f32', 'q.f32', 'logic.u8', 'ook', and 'vcd'.

Parameters must be separated by non-alphanumeric chars and are case-insensitive.
Overrides can be prefixed, separated by colon (':')

E.g. default detection by extension: path/filename.am.s16
forced overrides: am:s16:path/filename.ext