escputil - Man Page

escputil [ -P printer | -r device ] [ -m model ] [ -S ] [ -C ] [ -p ] [ -u ] [ -c | -n | -a | -i | -d | -o | -s | -l | -M | -h ] [ -q ]

escputil is a command line utility to perform various maintenance tasks on Epson Stylus inkjet printers.  These tasks include head alignment, head cleaning, nozzle check, printer identification, and retrieval of ink level from the printer.

escputil accepts the following options:

-P,  --printer-name=printer

Specify the name of the printer to operate on.  The default is the default system printer.

-r,  --raw-device=device

Specify the name of the device to write to directly rather than going through a printer queue. You must use this (rather than specifying a printer) when retrieving ink levels or identifying the printer, or if you wish to perform head alignment without specifying the printer model.

-m,  --model=model

Specify the precise printer model for head alignment.

-u,  --new

The printer is a new printer (Stylus Color 740 or newer).

-S,  --short-name

Print the short name of the printer with --identify.

-C,  --choices

Specify the number of pattern choices for alignment.

-p,  --patterns

Specify the number of sets of patterns for alignment.

-c,  --clean-head

Clean the print head.  This can also be performed from the printer front panel.

-n,  --nozzle-check

Print a nozzle test pattern.  Dirty or clogged nozzles will show as gaps in the pattern.  If you see any gaps, you should run a head cleaning pass or two.

-a,  --align-head

Align the print head.  CAUTION: Misuse of this option may result in poor print quality and/or damage to the printer.  You must either specify the printer model with the -m option, or use the raw printer device to allow escputil to detect the printer model.

-i,  --ink-level

Obtain the ink level from the printer.  This requires read/write access to the raw printer device.

-d,  --identify

Query the printer for make and model information. This requires read/write access to the raw printer device.

-o,  --align-color

Align the color print head (used by Stylus Color 480 and 580 only).  CAUTION: Misuse of this option may result in poor print quality and/or damage to the printer.

-s,  --status

Retrieve printer status.

-l,  --license

Display the license/warranty terms of this program.

-M,  --list-models

List the supported printer models.

-h,  --help

Display a list of all command line options.

-q,  --quiet

Suppress the banner.

USB-connected printers sometimes fail to identify or return ink levels.  You may have to repeat the command.  This is probably a timing issue in escputil, not a flaw in the printer.

Anything requiring bidirectional communication with the printer (identify, ink levels, or head alignment without specifying the printer model) requires read/write access to the printer port (for example /dev/lp0).  This may require these operations to be performed as root.  In addition, kernel support is required for bidirectional communication.  For Linux version 2.2, CONFIG_PRINTER_READBACK should be enabled; this is called CONFIG_PARPORT_1284 on 2.4 and later kernels.

If the printer is performing self-test or head cleaning on power up, the identify and ink level commands will time out, although the printer successfully receives the command.  The command will need to be reissued when the printer is quiescent.

Robert Krawitz.

Copyright ©  2000 Robert Krawitz (rlk@alum.mit.edu)

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

The homepage of the Gutenprint project from which this utility was contributed is located at http://gimp-print.sourceforge.net/.

lp(4), tunelp(8).