datalad-install - Man Page

datalad install [-h] [-s URL-OR-PATH] [-d DATASET] [-g] [-D Description] [-r] [-R LEVELS] [--reckless [auto|ephemeral|shared-...]] [-J NJOBS] [--branch BRANCH] [--version] [URL-OR-PATH ...]

This command creates local sibling(s) of existing dataset(s) from (remote) locations specified as URL(s) or path(s). Optional recursion into potential subdatasets, and download of all referenced data is supported. The new dataset(s) can be optionally registered in an existing superdataset by identifying it via the DATASET argument (the new dataset's path needs to be located within the superdataset for that).

If no explicit -s|--source option is specified, then all positional URL-OR-PATH arguments are considered to be "sources" if they are URLs or target locations if they are paths. If a target location path corresponds to a submodule, the source location for it is figured out from its record in the `.gitmodules`. If -s|--source is specified, then a single optional positional PATH would be taken as the destination path for that dataset.

It is possible to provide a brief description to label the dataset's nature *and* location, e.g. "Michael's music on black laptop". This helps humans to identify data locations in distributed scenarios.  By default an identifier comprised of user and machine name, plus path will be generated.

When only partial dataset content shall be obtained, it is recommended to use this command without the `get-data` flag, followed by a `get` operation to obtain the desired data.

NOTE

Power-user info: This command uses git clone, and git annex init to prepare the dataset. Registering to a superdataset is performed via a git submodule add operation in the discovered superdataset.

URL-OR-PATH

path/name of the installation target. If no PATH is provided a destination path will be derived from a source URL similar to git clone.

-h,  --help,  --help-np

show this help message. --help-np forcefully disables the use of a pager for displaying the help message

-s URL-OR-PATH, --source URL-OR-PATH

URL or local path of the installation source. Constraints: value must be a string or value must be NONE

-d DATASET, --dataset DATASET

specify the dataset to perform the install operation on. If no dataset is given, an attempt is made to identify the dataset in a parent directory of the current working directory and/or the PATH given. Constraints: Value must be a Dataset or a valid identifier of a Dataset (e.g. a path) or value must be NONE

-g,  --get-data

if given, obtain all data content too.

-D DESCRIPTION, --description DESCRIPTION

short description to use for a dataset location. Its primary purpose is to help humans to identify a dataset copy (e.g., "mike's dataset on lab server"). Note that when a dataset is published, this information becomes available on the remote side. Constraints: value must be a string or value must be NONE

-r,  --recursive

if set, recurse into potential subdatasets.

-R LEVELS, --recursion-limit LEVELS

limit recursion into subdatasets to the given number of levels. Constraints: value must be convertible to type 'int' or value must be NONE

--reckless [auto|ephemeral|shared-...]

Obtain a dataset or subdatset and set it up in a potentially unsafe way for performance, or access reasons. Use with care, any dataset is marked as 'untrusted'. The reckless mode is stored in a dataset's local configuration under 'datalad.clone.reckless', and will be inherited to any of its subdatasets. Supported modes are: ['auto']: hard-link files between local clones. In-place modification in any clone will alter original annex content. ['ephemeral']: symlink annex to origin's annex and discard local availability info via git-annex-dead 'here' and declares this annex private. Shares an annex between origin and clone w/o git-annex being aware of it. In case of a change in origin you need to update the clone before you're able to save new content on your end. Alternative to 'auto' when hardlinks are not an option, or number of consumed inodes needs to be minimized. Note that this mode can only be used with clones from non-bare repositories or a RIA store! Otherwise two different annex object tree structures (dirhashmixed vs dirhashlower) will be used simultaneously, and annex keys using the respective other structure will be inaccessible. ['shared-<mode>']: set up repository and annex permission to enable multi-user access. This disables the standard write protection of annex'ed files. <mode> can be any value support by 'git init --shared=', such as 'group', or 'all'. Constraints: value must be one of (True, False, 'auto', 'ephemeral') or value must start with 'shared-'

-J NJOBS, --jobs NJOBS

how many parallel jobs (where possible) to use. "auto" corresponds to the number defined by 'datalad.runtime.max-annex-jobs' configuration item NOTE: This option can only parallelize input retrieval (get) and output recording (save). DataLad does NOT parallelize your scripts for you. Constraints: value must be convertible to type 'int' or value must be NONE or value must be one of ('auto',) [Default: 'auto']

--branch BRANCH

Clone source at this branch or tag. This option applies only to the top-level dataset not any subdatasets that may be cloned when installing recursively. Note that if the source is a RIA URL with a version, it takes precedence over this option. Constraints: value must be a string or value must be NONE

--version

show the module and its version which provides the command

datalad is developed by The DataLad Team and Contributors <team@datalad.org>.